AddPac VoiceFinder AP2120 User's Guide Page 90
- Page / 355
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
VoiceFinder AP2120 VoIP Gateway User’s Guide Version 1.00
AddPac Technology Co., Ltd. -
90 -
4.5.3. OSPF Configuration
OSPF(Open Shortest Path First) is IGP (Interior Gateway Procotol) using Link State
Algorithm developed by OSPF Working Group of IETF(Internet Engineering Task
Force). OSPF is designed to support IP network with tagging of routing
information of sub-network. Also, it offers Packet Authentication with neighbor
gateways and utilizes IP multicase when sharing Routing information packet.
VoiceFinder AP2120 Gateway support OSOPF Version 2 described at Internet
RFC 1583. The below describes OSPF functions of VoiceFinder AP2120
Gateway
z Stub Area : Supports definition of Stub Area.
z Route Redistribution : Redistribute Routing information of IP routing protocol
to other routing procotols.
z Authentication : Supports Plain Text and MD5 Authentication among
Neighboring Gateways in an area.
z Routing Interface Parameter : The administrator can configure interface
parameters such as Interface output cost, retransmission interval, interface
transmit delay, router priority authentication key.
z ABR (Area Boarder Router) : It supports Area Border Routers function when
a Gateway exists on two different OSPF areas.
Network with OSPF has several Area include Back-bone area in one routing
domain.
z Routing domain: An area where routing is processed with one routing
protocol. If a network with different routing protocol is connected, it is
regarded as outside network by OSPF. One (1) OSPF routing doman
consists of one back-bone Area and several Areas.
z Area : a combination of several networks, and each Area has network
diagram called condition database. All the gateways at the same area
has the same condition database. These Areas can communicate with
Information
- VoiceFinder 1
- [ Contents ] 3
- About this document 9
- AddPac Technology Co., Ltd 10
- [Symbols and Legends] 12
- Warning 12
- Caution 12
- VoiceFinder AP2120 VoIP 게이트웨이 15
- 1.2. Main Features 16
- 2.1. Unpacking 22
- 2.2. Parts and decriptions 24
- Rear View of AP2120 26
- AP-E&M8 31
- AP-FXS4O4 32
- 3.1. Installation 37
- 3.1.2. Console Connection 38
- Port Configuration Settings 39
- 4.1. Gateway Booting 48
- 1 router# 50
- 4.2. Commands 52
- Command Description 55
- Commands Description 56
- [Procedures] 63
- 4.4. Ethernet Configuration 65
- 4.4.2. PPPoE Configuration 70
- 4.5. Routing Configuration 79
- 4.5.2. RIP Configuration 84
- 4.5.3. OSPF Configuration 90
- 4 : permit ip any any 104
- Information 105
- [NAT Glossaries] 106
- [Procedure] 107
- Configuration 115
- [Procedure-DHCP Server] 117
- Optional Commands 118
- DHCP Type = RELAY 121
- Next Server = 151.1.12.1 121
- 4.10. Traffic Management 129
- 4.11. SNMP Configuration 135
- Send a message 138
- Send a message indicating 138
- 4.13.1. Logging Command 148
- 4.13.2. Show commands 149
- 4.13.3. Debug Commands 153
- File Management 156
- 4.14.2. Password Recovery 157
- 5.1.1. Voice Over IP 165
- There 167
- 5.1.3. Dial Peer 169
- 5.1.4. Voice ports 170
- IP Cloud 176
- Destination 176
- Voice Port 187
- 5.3.4.3. Call barring 188
- Step Command Description 196
- 60 PIN CONNECTOR 199
- RJ45_4PORT 199
- Exits configuration 207
- 5.7.2.1. dial-peer hunt 215
- 5.7.2.1.5. Example 216
- 5.7.2.2.1. Syntax 217
- 5.7.2.2.2. Default value 217
- 5.7.2.2.3. Command Mode 217
- 5.7.2.2.4. Usage Guideline 217
- 5.7.2.2.5. Example 218
- 5.7.2.3.1. Syntax 218
- 5.7.2.3.2. Default Value 219
- 5.7.2.3.3. Command Mode 219
- 5.7.2.3.4. Usage Guideline 219
- 5.7.2.3.5. Example 219
- 5.7.2.4. dial-peer voice 220
- 5.7.2.5. gateway 222
- 5.7.2.6. num-exp 223
- 5.7.2.6.5. Example 225
- 5.7.2.7. translation-rule 226
- 5.7.2.8. voice-port 227
- 5.7.2.8.5. Example 228
- 5.7.2.9.1. Syntax 228
- 5.7.2.9.2. Default Value 228
- 5.7.2.9.3. Command Mode 229
- 5.7.2.9.4. Usage Guideline 229
- 5.7.2.9.5. Example 229
- 5.7.2.10.1. Syntax 230
- 5.7.2.10.2. Default Value 230
- 5.7.2.10.3. Command Mode 230
- 5.7.2.10.4. Usage Guideline 230
- 5.7.2.10.5. Example 230
- 5.7.2.11.1. Syntax 231
- 5.7.2.11.2. Default Value 231
- 5.7.2.11.3. Command Mode 231
- 5.7.2.11.4. Usage Guideline 231
- 5.7.2.11.5. Example 232
- 5.7.2.12. voice service 233
- 5.7.2.13. voip-interface 234
- 5.7.2.13.5. Example 235
- 5.7.3.1. comfort-noise 236
- 5.7.3.2. connection 237
- 5.7.3.2.5. Example 238
- 5.7.3.3.1. Syntax 238
- 5.7.3.3.2. Default Value 238
- 5.7.3.3.3. Command Mode 238
- 5.7.3.4. echo-cancel 239
- 5.7.3.5. input gain 240
- 5.7.3.5.4. Usage Guideline 241
- 5.7.3.5.5. Example 241
- 5.7.3.7. output gain 243
- 5.7.3.8. polarity-inverse 244
- 5.7.3.9. ring number 245
- 5.7.3.9.4. Usage Guideline 246
- 5.7.3.9.5. Example 246
- 5.7.3.10.1. Syntax 246
- 5.7.3.10.2. Default Value 247
- 5.7.3.10.3. Command Mode 247
- 5.7.3.10.4. Usage Guideline 247
- 5.7.3.10.5. Example 247
- 5.7.3.11.4. Usage Guideline 248
- 5.7.3.11.1. Syntax 248
- 5.7.3.11.2. Default Value 248
- 5.7.3.11.3. Command Mode 248
- 5.7.3.13.5. Example 251
- 5.7.3.14.1. Syntax 251
- 5.7.3.14.2. Default Value 251
- 5.7.3.14.3. Command Mode 251
- 5.7.3.14.4. Example 251
- 5.7.3.15.1. Syntax 252
- 5.7.3.15.2. Default Value 252
- 5.7.3.15.3. Command Mode 252
- 5.7.3.15.4. Example 252
- 5.7.3.18.2. Default Value 255
- 5.7.3.18.3. Command Mode 255
- 5.7.3.18.4. Usage Guideline 255
- 5.7.3.18.5. Example 255
- 5.7.3.19.1. Syntax 256
- 5.7.3.19.2. Default Value 256
- 5.7.3.19.3. Command Mode 256
- 5.7.3.19.4. Usage Guideline 256
- 5.7.3.19.5. Example 257
- 5.7.4. Dial Peer Commands 258
- 5.7.4.1. answer-address 258
- 5.7.4.2. codec 259
- 5.7.4.2.2. Default Value 260
- 5.7.4.2.3. Command Mode 260
- 5.7.4.2.4. Usage Guideline 260
- 5.7.4.2.5. Example 260
- 5.7.4.3.1. Syntax 261
- 5.7.4.3.2. Default Value 261
- 5.7.4.3.3. Command Mode 261
- 5.7.4.3.4. Usage Guideline 261
- 5.7.4.3.5. Example 261
- 5.7.4.4.1. Syntax 262
- 5.7.4.4.2. Default Value 262
- 5.7.4.4.3. Command Mode 262
- 5.7.4.4.4. Usage Guideline 262
- 5.7.4.4.5. Example 263
- 5.7.4.5. dtmf-relay 264
- 5.7.4.6. forward-digits 265
- 5.7.4.6.2. Default Value 266
- 5.7.4.6.3. Command Mode 266
- 5.7.4.6.4. Usage Guideline 266
- 5.7.4.6.5. Example 266
- 5.7.4.7. huntstop 267
- 5.7.4.8. port 268
- 5.7.4.9. preference 269
- 5.7.4.10. prefix 270
- 5.7.4.11. register 271
- 5.7.4.11.1. Syntax 272
- 5.7.4.11.2. Default Value 272
- 5.7.4.11.3. Command Mode 272
- 5.7.4.11.4. Usage Guideline 272
- 5.7.4.11.5. Example 272
- 5.7.4.12. sid 273
- 5.7.4.13. session target 274
- 5.7.4.14. polarity-inverse 275
- 5.7.4.16.1. Syntax 277
- 5.7.4.16.2. Default Value 277
- 5.7.4.16.3. Command Mode 277
- 5.7.4.16.4. Usage Guideline 277
- 5.7.4.17. vad 278
- 5.7.4.17.5. Example 279
- 5.7.4.18.1. Syntax 279
- 5.7.4.18.2. Default Value 279
- 5.7.4.18.3. Command Mode 279
- 5.7.4.18.4. Usage Guideline 280
- 5.7.4.18.5. Example 280
- Configuration Command 281
- 5.7.5.1. announcement 281
- 5.7.5.2. codec preference 282
- 5.7.5.3. counter 283
- 5.7.5.4. discovery 284
- 5.7.5.5. fax protocol 285
- 5.7.5.6. fax rate 286
- 5.7.5.6.2. Default Value 287
- 5.7.5.6.3. Command Mode 287
- 5.7.5.6.4. Usage Guideline 287
- 5.7.5.6.5. Example 287
- 5.7.5.7. h323 call start 288
- 5.7.5.8. gkip 289
- 5.7.5.9. h323 call channel 290
- 5.7.5.9.1. Syntax 291
- 5.7.5.9.2. Default Value 291
- 5.7.5.9.3. Command Mode 291
- 5.7.5.9.4. Usage Guideline 291
- 5.7.5.9.5. Example 291
- 5.7.5.10.1. Syntax 292
- 5.7.5.10.2. Default Value 292
- 5.7.5.10.3. Command Mode 292
- 5.7.5.10.4. Usage Guideline 292
- 5.7.5.11. h323-id 293
- 5.7.5.12. lightweight-irr 294
- 5.7.5.13. max-digits 295
- 5.7.5.14. password 295
- 5.7.5.15. public-ip 296
- 5.7.5.16. register 297
- 5.7.5.17. rule 298
- 5.7.5.17.1. Syntax 299
- 5.7.5.17.2. Default Value 299
- 5.7.5.17.3. Command Mode 299
- 5.7.5.17.4. Usage Guideline 299
- 5.7.5.17.5. Example 300
- 5.7.5.18.1. Syntax 301
- 5.7.5.18.2. Default Value 301
- 5.7.5.18.3. Command Mode 301
- 5.7.5.18.4. Example 301
- 5.7.5.19.1. Syntax 302
- 5.7.5.19.2. Default Value 302
- 5.7.5.19.3. Command Mode 302
- 5.7.5.19.4. Usage Guideline 302
- 5.7.5.20. timeout 303
- 5.7.5.20.2. Default Value 304
- 5.7.5.20.3. Command Mode 304
- 5.7.5.20.4. Usage Guideline 304
- 5.7.5.20.5. Example 304
- 5.7.6.1. clear h323 call 307
- 5.7.6.2. clear voice port 308
- 5.7.6.3. show call active 308
- 5.7.6.4.2. Default Value 310
- 5.7.6.4.3. Command Mode 310
- 5.7.6.4.4. Usage Guideline 310
- 5.7.6.4.5. Example 310
- 5.7.6.5.1. Syntax 310
- 5.7.6.7. show dial-peer 312
- 5.7.6.10. show gateway 314
- 5.7.6.11. show num-exp 315
- 5.7.6.13. show user-class 317
- 5.7.6.14. show voice port 318
- 5.7.6.16. debug voip call 320
- 5.7.6.17. debug voip 321
- A-2 LAN/WAN Service 325
- ITEM Specification Remark 327
Related products and manuals for Gateways/controllers AddPac VoiceFinder AP2120
(302 pages)© 2020, manymanuals.com. All rights reserved. | 4.788 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals